Abel Flash Point Tester 

 REDWOOD VISCOMETERS

(AS PER IP 70)
Description these viscometers conforms to the requirements of IP 70. This method determines the viscosity of an oil as a time of flow in seconds through Rewood Viscometer. It does not measure viscosity in the absolute units. This method is primarily intended for the determination of the viscosity of any petroleum product which flows in a Newtonian manner. Two forms of viscometer are available. The Redwood No I and No II .These instruments are suitable for use with oils having flow time, at the temperature of the test, not less than 30 secs. When flow time with No. I instruments exceeds 2000 sec. The No II instruments shall be used. The complete instrument comprises of stove hammer finished shield, stainless steel bath with electrical heating arrangements,suitable to operate on ,220 volts A.C Mains or gas heating arrangements, with tap, silver plated oil cup with precision stain less steel jet, cup cover, ball valve, thermometer clip, stirrer and M.S sheet stand with levelling screws.

REDWOOD VISCOMETER NO I

T 8001          RV No I  gas heated without burner                                              

T 8002           RV No I  Electrically heated with energy regulator                         

T 8003           RV No I  Electrically heated with solid state elec. Regulator          

T 8003 - A                                     RV No.I Electrically heated with varriac (copper coil)  

T 8003 - B     RV No I Electrically heated with digital temp. controller                           

REDWOOD VISCOMETERS NO II

T 8004           RV No II Gas heated without burner                                               

T 8005           RV No II Electrically heated with energy regulator                          

T 8006           RV No II Electrically heated with solid state elec. Regulator           

T 8006 – A     RV No II Electrically heated with varriac (copper coil)                     

T 8006 – B     RV No II Electrically heated with Digital temp.controller                

MULTIPLE REDWOOD VISCOMETER

Made of SS bath big enough to accommodate 3 Redwood No. I cups and

2 Redwood No. II cups. Stirring is done by a FHP motor in the bath. It is supplied

with 5 complete assemblies of brass cups alongwith jets temp can be controlled

by following means.

T 8000   MRV with thermostatically controlled                                                                                                      

 T 800   MRV with digital temp. controller                                                                                                                                     

ESSENTIAL ACCESSORIES

1.1                Thermometer IP 8C                                                                                

1.2                Thermometer IP 9C                                                                                

1.3                Thermometer IP 10C                                                                              

1.4                Flask receiver 50 ml. capacity                                                                

OPTIONAL ACCESSORIES

1.5                Spare cup with valve for RV No. I                                                          

1.6                Spare cup with valve for RV No. II                                                          

1.7                Spare heater for RV No. I                                                                      

1.8                Spare heater for RV No. II                                                                      

1.9                Spare ball valve for RV No. I & II                                                            

1.10              Polished teakwood carrying case for RV No. I                                        

1.11              Polished teakwood carrying case for RV No. II                                       

SAYBOLT VISCOMETER

(As per ASTM D88)

           The apparatus consists of stainless steel bath and universal and furol jets of

            stainless   steel stirring is done manually with turn table arrangement

T. 80543        Say bolt viscometer elec. heated with energy regulator                             

T. 8054         Say bolt viscometer elec. heated with solid state

                    electronic regulator.                                                                               

T. 8055         Say bolt viscometer elec. with voltage varriac

                    (copper oil)                                                                                            

T. 8055A       Saybolt viscometer elec. heated with four saybolt

                    saybolt tubes and thermo statically controlled.                                         

T. 8055B       Saybolt viscometer Elec. with four saybolt tubes

                    and ditital temp. controller cum indicator                                                  

ESSENTIAL ACCESSORIES

2.1                Spare flask 60 ml.                                                                                 

2.2                Spare strainer for filtering oil                                                                  

2.3                Thermometer ASTM 17C to 22 C(any)                                                     

OPTIONAL ACCESSORIES

2.9                Spare cup with jets.                                                                               

2.10              Jet Universal / Furol                                                                              

2.11              Heater                                                                                                  

2.12              Sprit level                                                                                             

2.13              Withdrawal Tube                                                                                    

2.14              Polished Teakwood carrying case.                                                         

ENGLER VISCOMETER

(AS PER IP 212,BS 434, ASTM D490)

It is used for the determination of viscometer of lubricating and fuel oils. The app consistsof S.S.Water bath with oil cup and its lid, manual stirrer is provided inside the bath. A thermometer socket is provided on oil cup lid. It has 500 watt heater, two jets wooden and ebonite. Operates on 220 volts AC mains.

T 8050           Engler Viscometer elec. Heated without regulator                                    

T 8051           - do “ With Energy regulator                                                                  

T 8052           - do“ with solid state electronic regulator                                               

ESSENTIAL ACCESSORIES

3.1                Flask 200 ml                                                                                         

3.2                Thermometer ASTM 23 C to 25C (any)                                                    

OPTIONAL ACCESSORIES

3.3                Ebonite/ wooden valve                                                                           

3.4                Polished teak wood carrying case                                                           

3.5                Spare heater for above                                                                           

STANDARD TAR VISCOMETER

(As per ASTM D88)

This method determines the viscosity of cutback bitumenand road oil in arbitary units using the standard tar viscometer. Two forms of the app are available differing in size of the orifice i.e. larger orifice 10mm and smaller 4mm. The cup is used at 25 deg C exceeds 50deg C sec. The  mm cup is used at a temperature of 25 deg C for materials whose viscosity is less less than 15 sec. In the 10mm cup at 25 deg C. It consists of a bath with cup of 10mm/4mm orifice and sleeve, stirring, with ball lifting clip and ball. The assembly is kept on a suitable stand with leveling screws, suitable to operate on 220 volts AC mains.

T 8007          Electrically heated with energy regulator                                                  

T 8008          Electricallt heated with solid state elect. Regulator                                   

T 8009          Electrcally heated with varriac( copper coil)                                              

T 8009(A)      Multiple test app for 5 cups digitally controlled temperature                       

ESSENTIAL ACCESSORIES

4.1                                Flask receiver 100ml                                                                              

4.2                                Thermometer IP 8 C                                                                              

4.2                                Thermometer IP 9 C                                                                              

4.3                                Thermometer IP 10 C                                                                             

OPTIONAL ACCESSORIES

4.5                Silver plated cup 10mm/4mm orifice                                                        

4.6                Polished teakwood carrying case                                                           

FLOWCUP VISCOMETER

As per IS 3944

Flowcup Viscometer complete with stand and level with any of the jets

No. 2, 3, 4, 5, & 6

T 9001           Flowcup Viscometer                                                                              

OPTIONAL ACCESSORIES

5.1                Brass cup with any type of jet                                                                

KINEMATIC VISCOMETER BATH

As per IP 71 & IS 1448

This viscometer Bath is used to maintain the correct-temperature for estimating Kinematic viscosity of oil & petroleum products various Viscometers may be fixed as an integral part of the bath. The bath is rectangular in shape. Inside tank made of stainless steel. Toughened glass is provided at the front & rear for visibility inside the bath. A motorised stirrer is provided and it is supplied with Viscometer tube holders with cover.

The temperature of the bath from ambient to 1000C may be controlled by different Models given below :

T 8038          K.V. Bath with Toughend glass Window

                    Chamber size : 12" × 9" × 12" (S.S.)

                    Accommodation : 4 Viscometers Temp controlled by                                

                    (a) Contact Thermometer Acc 0.10C

                    (b) Digital temp. Controller cum indicator Acc 0.10C                                  

T 8039          K.V. Bath with toughened glass window.

                    Chamber size . 12" × 12" × 12" (S.S.)

                    Acc. 6 Viscometers Temp. Controlled by

                    (a) Contact thermometer Acc 0.10C                                                         

                    (b) Digital Temp. Controller cum indicator Acc. 0.10C                                

T 8040          KV Bath with toughened glass window

                    Chamber size 18"× 12" ×12"

                    Acc. 8 Viscometers Temp. controlled by

                    (a) Contact thermometer                                                                         

                    (b) Digital Temp. Controller cum indicator                                                 

ESSENTIAL ACCESSORIES

6.1                U Tube Viscometer Type BS/U                                                               

6.2                -do- Reverse flow Type BS/IP/RF                                                           

6.3                Suspended level Viscometer type BS/IP/SL                                           

6.4                Canon Fenske Viscometer type BS/IP/CF                                               

6.5                -do- Viscom for opaque liquids                                                             

Note :           Mention size & Viscosity Range Along with order

OPTIONAL ACCESSORIES

6.6                Electric FMP pump for stirring by circulation                                          

                    of liquid instead of FHP Motor stirrer

6.7                Viscometer holder                                                                                 

6.8                Copper Coil cooling Tube                                                                      

6.9                Light Arrangement                                                                                 

ABELS FLASH PT APPARATUS

As per IP 33/59 & IS 1448 P: 20

This method determines the closed cup flash points of petroleum products and mixtures to ascertain whether they give off inflammable vapour below 730F or 490C The instrument comprises of electric heater at bottom and is supplied with a Water bath cup cover fitted with stirrer, thermometer, sockets & stand.

T. 8010        Abels Flash Pt. Apparatus as per IP 170 with

                    refigeration system range-200 to 700C                                               

T. 8011        Abels Flash Pt. Apparatus electrically heated

                    with Energy regulator but concealed hot plate.                                  

T. 8012        Abels Flash Pt. apparatus electrically heated temperature

                    controlled by digital temp. controller cum indicator                            

T. 8013        Abels Flash Pt. Apparatus electrically heated with

                    energy regulator.                                                                                

T. 8014        Abels Flash Pt. Apparatus electrically heated with

                    solid state electronic regulator                                                           

T. 8015        Abels Flash Pt. Apparatus electrically heated with

                    varriac (copper Coil).                                                                          

       Note :  For gas test jet assemblies Kindly specify in your order extra Rs 200/-

ESSENTIAL ACCESSORIES

7.1               Thermometer Abeles Oil Cup : with Brass Collor                              

7.2               Thermometer Abeles Oil Cup Wide Range with Brass collor            

7.3               Thermometer Abeles water bath with Brass collor                            

7.4               Thermometer Abeles water bath wide Range Brass collor               

OPTIONAL ACCESSORIES

7.5               Spare cup for the apparatus                                                               

7.3               Spare Top (Cover assembly) with shutter mechanism                     

7.7               Spare Nichrome heating element                                                      

7.8               Polished teakwood carrying case                                                      

7.9               Concealed hot plate for above                                                           

7.10             Pendulum for Measuring time in stokes.                                            

7.11              Energy regulator for above with box fitting                                             

PENSKY MARTEN's apparatus

As per IP 34 ASTM93-58T & ISI 1448 (PI) 1960 & 1209-1953 Method 8

This method is intended for the determination of the open flash point and fire point of petroleum products except when the clean and open cup is specified.

The Apparatus consists of brass test cup with handle removable cover, with spring operated rotating shutter for smooth operation, having a pilor jet, stirrer with flexible shaft. the assembly rest in air bath which is covered with umbrella shaped S.S. Steel top. The cup if fitted with insulated handle and locking arrangement near cup flange. The assembly rests on a round shaped heater with different temperature regulation systems suitable for operation on 220 V AC.

T 8016           Electrically heated with energy regulator control                                      

T 8016 – A     -do- with separate box for regulator                                                       

T 8017           Electrically heated built in energy regulator,concealed hot plate               

T 8017 – A     -do- with separate box for energy regulator                                            

T 8018           Elect. Heated with E regulator,FHP stirrer with stand                               

T 8019           Semi automatic (introduction of test flame automatic)                             

T 8020           Elect heated with varriac (copper coil)                                                    

T 8020 – A     -do- with concealed hot plate for heating                                                

T 8021           Elect. Heated with concealed hot plate,varriac,FHP stirrer                       

T 8021 – A     Elect heated with FHPstirrer concealed hot plate& digital temp.indicator,                                                    

Note : For gas test jet assemblies kindly specify in your order.

ESSENTIAL ACCESSORIES

8.1               Thermometer IP 15C                                                                         

8.2               Thermometer IP 16C                                                                         

OPTIONAL ACCESSORIES

8.3  Open clip for converting close model to open Cup test                     

                    model As per IP 35                                                                             

8.4               Spare cup with handle                                                                        

8.5               Space cover Assembly                                                                      

8.6               Spare Nichrome element                                                                   

8.7               Concealed hot plate for above                                                           

8.8               Polished teakwood carrying case                                                      

8.9                Gas connection tube with “Y� joint                                                          

CLEAVELAND FLASH & F. PT. APPARATUS

(As per IP 36 & IS 1448)

This apparatus is used for determination of flash and fire pt. of petroleum products except fuel oils and those having an open cup flash below 790C. The apparatus consists of a cup, heating plate of spcific dimensions, thermometer clip and test flame attachment with service joints for passing over test liquids surface in the prescribed manner. Heating is controlled by means of energy regulator fitted to apparatus Suitable for operation on 220 V. AC.

T 8022          Elect. Heated with energy regulator                                                         

T 8022 – A     Elect. Heatedwith oil test & energy regulator                                           

T 8022 – B     Elect. Heated,E regulator, with both option oil test/gas test                     

T 8022 – C     Elect heated with varriac (copper coil)                                                    

T 8022 – D    Elect. Heated with varriac and both oil/gas option                                   

T 8022 – E     Elect heated with digital temp indicator                                                  

T 8022 – F     - do – with both options of Gas test/ Oil test                                          

ESSENTIAL ACCESSORIES

9.1               Thermometer IP 28C                                                                         

OPTIONAL ACCESSORIES

9.2 Spare cup with handle                                                                        

9.3 Concealed hot plate.                                                                           

9.4  Polished teakwood carrying case.                                                     

9.5     Nichrome element.                                                                             

9.6   

DISTILLATION APPARATUS

(As per IP 123, 24 IS448: 18)

This apparatus is used for determination of distillation characteristics of petroleum products. The instrument consists of metal shield to support distillation flask provided with a geared height adjusting device. It has a slot for vapour tube and a glass window in front for inside view. It is supplied with a cooling Bath with condensor tube & stand.

T.8033          Distillation App. Elect. heated with energy regulator

                    with geared unit for height adjustments.                                                   

T.8034          Distillation App. Elect. heated with voltage

                    varriac (copper oil)                                                                                 

T.8035          Twin Distillation App. electrically heated with

                    Energy Regulators                                                                                 

T.8035(A)      Twin Distillation App. with Voltage Varriacs (copper coil)                           

ESSENTIAL ACCESSORIES

10.1              Thermometer IP5 C                                                                                

10.2              Thermometer IP6 C                                                                                

10.3              Distillation flask 125 ml.                                                                         

10.4              Crow type receiver 250ml.                                                                      

OPTIONAL ACCESSORIES

10.5              Spare Asbestos Board 32, 38, 50 or 70mm hole Dia                               

10.6              Spare Nichrome Element                                                                       

HEAVY DUTY DISTILLATION APP.

T9002            Same as above but heat insulation by cement Asbestos

                    sheet on all sides with adjustable heater height supplied

                    with voltage varriac (copper coil)                                                            

PENETROMETER APPARATUS

As per IP 49, 50 & 167 IS 1448

This apparatus is used for penetration test on a wide variety of materials such as grease, petroleum, bitumen, tar, wax, polish, food stuff, rubber asphalt and pharmaceutical creams. A given force is applied over a given period of time and the depression thus made in the sample is measured in tenths of a millimeter and expressed as penentration. It consists of a head support mounted on a vertical rod which can be a adjusted for height. A reck and pinion and pointer assembly provides fine adjustment of needle tip to sample and incorporate a slipping clutch and subsequent resetting a sample and accurate operation. The dial graduated from 0 to 400 in one tenth millimeter sub division.

T.8028          Penetromete app.with container, weights,with penetration needle

T.8029          Pwenetrometer app. with container,weights and hollow cone       

T.8029 A       Penetrometer apparatus with timer and electrical arrangement    

T.8029 B       ……….do……… but digital                                                           

ESSENTIAL ACCESSORIES

11.1              Thermometer IP38C.                                                                              

OPTIONAL SPARES

11.2              Spare penetration needle two Numbers                                                  

11.3              Spare penetration solid come with heavy Polish.                                    

11.4              Spare Penetration hollow cone with heavy Polish.                                   

11.5              Grease worker hand operated with oil seal.                                             

11.6              Grease cutter as per IP 50.                                                                    

11.7              Constant temperature water bath with energy regulator                            

11.8              Transfer Dish.                                                                                       

As per IP 13, ASTM D-189

This app is used to determine the amount of carbon deposit when an oil is evaporated under specific condition. The carbon residue values of crude oil, residuan etc. Which are useful in the manufacturer of various lubricants. The app. consists of spun sheet Iron Crucible, Sheet Iron Hood, sheet Iron block made to size as per specification and stand with Triangular wire bridge.

T8043.          Conradson Carbon Residue App. with gas

                    burner (single Tes).                                                                                

T8014           -do- with gas burner (four test)                                                                

OPTIONAL ACCESSORIES

12.1              Gas burner                                                                                            

12.2              Inner Crucible withlid.                                                                             

12.3              Outer Crucible with lid.                                                                           

CARBON RESIDUE APP. (RAMSBOTTOM)

(As per IP14, ASTM D-524 & IS : 1448)

It is used to determine the amount of Carbon deposit when an oil is evaporated under specific conditions. The app. consists of a solid metal bath, having 6 wells to accommodated cocking bulbs. The heavy duty heating elements provided around the bath. Supplied with 6 cocking bulbs.

T8041           Ramsbottom carbon Reside App. with temp regulation by

                    energy regulator Thermocouple & pyrometer                                            

T8042           -do- Compact type, heat regulation by voltage Varriac

                    (copper-oil)                                                                                            

T8042           -do- Compact type with Digital Temperature controller,

                    & Indicator                                                                                            

OPTIONAL ACCESSORIES

13.1              Spare Cocking Bulb                                                                              

13.2              Spare heating element                                                                           

13.3              Spare Syringe                                                                                       

COPPER STRIP CORROSION TEST APP.

As per IP 154 IS 1448

This method describes procedures for the detection of the corrosiveness to copper of airation gasoline, aviation furnace fuel, automotive gasoline, farmtractor, fuel dealers (standard) solvent diesel fuel, oil (distillate), and certain other petroleum products. The App. consists of a Bath large enough to accommodates 6 Bombs made as per specifications.

T-8067          Copper strip corrosion test App. Bath for 6 Bombs temp.

                    Controlled by means of digital temperature Controller

                    Cum indicator                                                                                        

ESSENTIAL ACCESSORIES

14.1              Stainless steel Bomb                                                                            

14.2              Vice single strip                                                                                    

14.3              Copper Strip (Set of three)                                                                    

14.4              Inspection tube                                                                                     

14.5              Test Tube                                                                                             

OPTIONAL ACCESSORIES

14.6              Vice for holding 6 strip                                                                          

MELTING POINT APP.

(As per IP 133 ASTM D-127-29)

This App. determines melting point of petroleum products. It consists of rectangular block of Aluminium with built in electric heating element. The temperature is controlled by means of energy regulator. An adjustable lens is provided for viewing exact melting point supplied without capillaries.

T-8056          Melting point Apparatus                                                                          

ESSENTIAL ACCESSORIES

15.1              Thermometer IP63C.                                                                              

BOMB CALORIMETER APP.

As per 1P 12

This method is suitable for the determination of the gross calorific values of liquid fuels, including airation fuels & sulphur contents of solid and liquid fuels. The bomb, body and lid are machined from corrosion resistant stainless steel rod. Cap approve 300 ml. It is provided with high pressure valve & Electrodes. The calromeus vessel water jacket, stirrer. FHP motor driven are provided as per IP standards. The App. is supplied with finely built Beckman thermometer, pellet press, ignition wire, pressure gauge on stand with copper pipe fitting & magnifying glass.

T-8066          Bomb Colori-meter App.                                                                         

T-8066A        Digital Bomb Calotri Meter.                                                                     

OPTIONAL ACCESSORIES

16.1              Spare Bomb                                                                                         

16.2              Neoprene washer for bomb                                                                   

16.3              Spare stainless steel Curable                                                                 

16.4              Spare motor Belt                                                                                   

CLOUD AND POUR PT. APP.

As per IP 15 IS 1448-1970

The pour point is the lowest temperature at which the oil will just fail to flow. The apparatus consists of the main cooling Bath made out of stainless steel sheet and stand unit with drain plug. The cover has provision for fitting thermometer and a filling apparatus for adding freezing mixture. A glass jar for containing oil, metal jacket disc and gasket as per specification are also provided.

T.8025          Cloud & Pour single test apparatus with

                    insulated body.                                                                             

T.8026          Cloud & Pour four test apparatus with

                    insulated body.                                                                             

T.8027          Cloud & pour six test apparatus with

                    insulated body                                                                              

T.8027A        Cloud & Pour App. with Ref. system

                    upto - 300C twin test App.                                                              

ESSENTIAL ACCESSORIES

17.1              Thermometer IP 1C                                                                                

17.2              Thermometer IP 2C                                                                                

OPTIONAL ACCESSORIES

17.3              Spare glass jar withcock                                                                        

17.4              Spare metal jacket with disc                                                                   

17.5              Polished teakwood carrying case                                                           

SOFTENING PT. APPARATUS (RING & BALL APPARATUS)

(Asper IP 58 7 IS 1205/1958)

This apparatus is meant for determination of softening point of Bituminous materials. Softening point is that temperature at which the specimen under test becomes soft enough to allow a steel ball of specific dimension to fall a required distance under test conditions. The apparatus consists of a glass beaker, ring stand, two steel balls with rings and ball guides and hand stirrer.

T.8023         Softening Pt. Apparatus Hand operated

                    with beaker.                                                                                                

T.8024         Softening Pt. Apparatus with electric motorised

                    stirrer and electric heater with temperature

                    regulator control                                                                                  

T.8024(A)     Softning Pt. App abov with digital tmp. Controller               

ESSENTIAL ACCESSORIES

18.1             Thermometer IP 60C                                                                         

18.2             Thermometer IP 61C                                                                         

OPTIONAL SPARES

18.3             Spare ring and ball centering guide with steel ball.                            

DROP POINT APPARATUS

(As per IP 31, IP 132, and ASTM D-566)

There are two types of apparatus depending upon the type of cup used. In method IP 31 the thermometer if fixed to assembly. In both type of apparatus one glass beaker, a test tube, a metalcup or cup assembly is provided. Strining is done by FHP electric motor the whole unit is kept on suitable electric heater with temperature regulator control.

T8030           Drop point Apparatus as per IP 31                                

T8031           Drop point Apparatus as pe rIP 132 &

                    ASTM 566                                                                  

OPTIONAL ACCESSORIES

19.1              Thermometer IP 40C                                                                              

19.2              Thermometer IP 41C                                                                              

19.3              Thermometer IP 62C Drop point special                                                 

19.4              Universal heater                                                                                    

SMOKE PT. APPARATUS

As per IP 571 & IS 1448

This methord describes a procedure for evaluating a kerosine without producing smoke.

T 8096          Smoke Point Apparatus                                            

WATER STILL (MANESTY TYPE)

The body is made of stainless steel sheet immersion heaters are safety ejection type. A constant water level & steam baffle is provided to take steam direct to the condensor. It can be opened easily for cleaning. It is supplied with wall brackets & electric chord.

        Catalog No.      Capacity            Rating                          

        T8078             2.0 ltrs./hr.           2 K.V.                           

        T8079             4.0 ltrs./hr.           4 K.V.                           

        T8080             7.0 ltrs./hr.           5 K.V.                           

        T8081            10.0 ltrs./hr.          6 K.V.                           

WATER STILL (BARNSTEAD TYPE)

The body double walled insulation & enamel painted. Unlike the Manesty type. The Barnstead type is Horizontal and is more convenient to use. Suitable for operation on 220 V. A.C.

        Catalog No.                   Capacity              Rating                       

             T8082                      5.0 ltrs./hr.             4 K.V.                             

             T8083                      8.0 ltrs./hr.             6 K.V.                             

             T8084                     10.0 ltrs./hr.            8 K.V.                             

ANILINE POINT APPARATUS

As per IP 2 IS 1448

Four Methords of determining the Aniline point are described of which methord A is suitable for most petroleum products. Methords B & C are for petroleum sprits which vapourise appreciable at the Aniline point & Methord D is for Petroleum products which are too dark for testing by Methord A.

T 8091          Aniline Point Apparatus Methord A Complete with Jacket                          

T 8092          Aniline Point Apparatus Methord B Electrically heated with

                    Motorised Stirrer                                                                                    

T 8093          Aniline Point Apparatus as per IP 277 U Tube methord Elec.

                    Heated with Motorised Stirrer                                                                  

T 8094          Aniline Point Apparatus for Volatile liquids Methords                                 

SMOKE PT. APPARATUS

As per IP 571 & IS 1448

This methord describes a procedure for evaluating a kerosine without producing smoke.

T 8096          Smoke Point Apparatus                                            

WATER STILL (MANESTY TYPE)

The body is made of stainless steel sheet immersion heaters are safety ejection type. A constant water level & steam baffle is provided to take steam direct to the condensor. It can be opened easily for cleaning. It is supplied with wall brackets & electric chord.

        Catalog No.      Capacity            Rating                          

        T8078             2.0 ltrs./hr.           2 K.V.                           

        T8079             4.0 ltrs./hr.           4 K.V.                           

        T8080             7.0 ltrs./hr.           5 K.V.                           

        T8081            10.0 ltrs./hr.          6 K.V.                           

WATER STILL (BARNSTEAD TYPE)

The body double walled insulation & enamel painted. Unlike the Manesty type. The Barnstead type is Horizontal and is more convenient to use. Suitable for operation on 220 V. A.C.

        Catalog No.                   Capacity              Rating                       

             T8082                      5.0 ltrs./hr.             4 K.V.                             

             T8083                      8.0 ltrs./hr.             6 K.V.                             

             T8084                     10.0 ltrs./hr.            8 K.V.                             

BATHS

WATER BATH SINGLE WALLED

It is made of stainless steel, top of the bath & concentric rings are Nickel plated, supplied with heating elements with automatic cut off device when dry, suitable to operate on 220 volts A.C.

Cat. No.            Chamber Size                 No. of Holes             Rating                       

T 8060              300×250×100                      6 (75mm)                1 K.V.                       

T 8061              300×400×100                    12 (75 mm)             1.5 K.V.                      

WATER BATH (DOUBLE WALLED)

Inner Bath is made of stainless steel & outer body is made of M.S. Sheet in between insulation of glass wool is provided. Its temperature is controlled by a thermostat from ambient to 1000C. Top of the bath & concentric rings are Nickel plated, suitable for 220 volts. A.C.

Cat. No.            Chamber Size                 No. of Holes             Rating                       

T 8062              300×250×100                      6 (75mm)                1 K.V.                       

T 8063              400×300×100                    12 (75 mm)             1.5 K.V.                      

WATER BATH (SEROLOGICAL)

Serological water Bath double walled inside tank of stainless steel & outer Body of M.S. with insulation temperature range from ambient to 1000C

Thermostatic controlled, suitable to operate on 220 V.A.C. main.

Cat. No.            Chamber Size                Racks           Thermostat        Digital Controller

T 8064A            450×400×175                      6                      

T 8064B            350×300×175                      4                      

WATER BATH (PRECISION CONSTANT TEMPERATURE)

Inside chamber is made of stainless steel sheet outer body of M.S. sheet, temperature is controlled by a Contact Thermometer or Digital temp controller with indicator. A Glass window is provided in the front for viewing.

Cat. No.            Chamber Size               Rating        Without Glass           With Glass

                                                                                    Window                  Window

T 8065              30×25×15                       1 K.V.                  

T 8066              45×35×20                       2 K.V.                  

Note : - Circuiting pump instead of motoised stirrer for any above model  Rs. 2000.00

OIL BATH (HIGH TEMPERATURE)

Temp. Range      :        Ambient + to 2000 accuracy + 100 upto 1000 & beyond 200C

Heaters              :        Immesion Type

Chamber & Lid    :        Made of Copper Sheet

Stirrer                 :        Heavy duty motor with regulation control on panel

Temp. Control by:        Digital Controller Cum Indicator

Cat. No.            Chamber Size (mm)            Rating                      

T 8067              350×250×200                        2 K.V.                      

T 8068              400×300×250                        3 K.V.                      

VISCO METER BATH (0 TO 80 DEGREE CENT.)

Ranger                                    :    00 to 800C

Chamber & Lid                        :    Made of S.S.

Stirrer                                   :    Heavy duty Motor, with Regulation Control on Pannel

Viewing                                   :    Through Glass Windows Provided

Temp. Control by                 :    Digital Temp. Controller accuracy +-0.10C

Accommodation                    :    4 Visco Meters

Cat No.             Inner Chamber Size (mm)   Rating                      

T8069               300×200×300                        1 K.V.                      

STIRRERS

Cat. No.            Motor Power               Speed Regulation       Cap. Ltr.                     

T8070               1/20 H.P.                             Varriac                      8                           

T8071               1/12 H.P.                             Varriac                  30-40                        

T8072               1/4 H.P.                               Varriac                  30-40                        

OVENS

Cat No.           Dimensions                Shelves          Rating                  Alu            S.S.

T 8073            350×350×350                    2                  1.0                         

T 8074            450×450×450                    2                  2.0                         

T 8075            600×600×600                    3                  3.0                         

OPTIONAL

1.                   Air Circulation Fan                                                             

2.                   Digital Display Prop. Temp. Controller                                

THERMOMETERS

ROOM THERMOMETER

T.9000            Wooden base wall mounting                    

T.9001            Plastic/fibre base wall mounting               

WET & DRY THERMOMETER

T.9002            Wooden base wall mounting                    

T.9003            Plastic/fibre wall mounting  

WHIRLING HYGROMETER

Cat. No.          Range               Filling               Base                    

T.9020            -5 to 500C           Spirit                 Wooden                

T.9021            -5 to 500C           Spirit                 Plastic                  

POCKET THERMOMETER

Cat No.           Range               Filling               Casing                 

T.9004            -5 to 105            Spirit                 Metal                    

T.9005            -5 to 105            Spirit                 Plastic                  

T.9006            -30 to 50            Spirit                 Metal                    

T. 9007           -30 to 50            Spirit                 Plastic                  

MAX & MIN. THERMOMETER

T. 9008           Wooden Base Wall Mounting                                   

T. 9009           Plastic / Fibre Base Wall Mounting                          

OIL & PETROLEUM TESTING INSTRUMENTS

FOR VISCOSITY

1.   Redwood No. I

2.   Redwood No. II

3.   Multiple R.V.

4.   Saybolt Viscometer

5.   Engler Viscometer

6.   Standard Tar Viscometer

7.   Flow Cup Viscometer

8.   Kinematic Viscometer

FOR FLASH PT. & FR PT.

1.   Able's Flash Pt.

2.   Pensky Martens

3.   Cleave land Flash & Fr. Pt.

FOR DISTILLING

1.   Distillation App.

2.   Heavy Duty Distillation App.

3.   Water Stills (Manesty)

4.   Water Stills (Barnstead)

OTHERS

1.   Aniline Pt. App.

2.   Bomb Calorimeter

3.   Carbon Residue (Con.)

4.   Carbon Residue (Ram's)

5.   Cloud & Pour

6.   Copper Strip

7.   Drop Pt.

8.   Melting Pt.

9.   Penetrometer

10. Smoke Pt. App.

11. Softening Pt. App.

BATHS

1.   Water Bath Single Wall

2.   Water Bath Double Wall

3.   Water Bath Serological

4.   Water Bath Precision

5.   Bath High Temperature

6.   Bath Viscometer

LAB APPLIANCES

1.   Stirrers

2.   Oven

THERMOMETERS

1.   Room Thermometers

2.   Wet & Dry Thermometers

3.   Whirling Hygrometer

4.   Pocket Thermometers

5.   Max & Min Thermometers

6.   Scoop Thermometers

7.   Concreate Thermometers

8.   Soil Thermometers

9.   Silage Thermometers

10. Industrial Thermometers